Monday 10 August 2009

Not hitting target gravity

Some home brewers maybe familiar with the deflated feeling. The one you get from (after six hours of brewing) finding your 1.060 strong ale has actually came out at 1.052. It doesn’t often happen, usually im within about 2 or 3 degrees off target gravity, but this time it was a bit more serious. As as other things the 34 bitterness units I aimed for may have been raised slightly changing the balance of this beer, but its always a good idea to asses where things may have went wrong.

How to hit gravity:

The core principle is to match up the percentage used of each grist component (malt or adjunct) with the extract in litre degrees obtained from each component. From these, and the known volume you’re brewing, you can work out quantitatively how much of each malt you will need to theoretically hit target gravity (given a theoretical 100% efficient extraction).

At this point you need to know the efficiency of your brewing system witch is derived from the difference in what extract you should get from the malts your putting (as just described) in comparison to the extract you actually get in the fermentation vessel. Additionally what you can do is get a gravity reading of wort from the copper (once its full) termed the copper up gravity. Under the same logic you can use this to get a gauge of the efficiency of your mash separation method (whether mash tun, lauter tun or mash filter), and what the gravity of the wort will be in the fermentation vessel. I have often contemplated using this method, but find it takes a little long to bring the temperature of the wort sample down when I have only minutes to return it to the just starting to boil copper.

Mashing in
That’s the basics, some other things to consider are the various factors that effect extracts, including:

Length of the copper boil; boiling longer drives off vapors condensing the worts sugar content. Very simple. In fact some strong ales such as Bass No1 barley wine rely of extreme boil lengths to maximize start gravities.


Malt quality; for example over or under modified malts can give poor extracts that can be harder to ferment due to insufficient wort nitrogen, watch out for them!

The mash separation system used and how the grain is prepared; For example the use of a mash filter over a mash tun gets a higher extract into the copper using a more finely ground grist. Mash tuns require coarsely ground malt that allows the malts husk material to act as a natural filter bed during run off, using a finer grist increases extract but the mash tun user risks losing the natural filtration from the in tact husk material. Secondly the grain is also sensitive to sparging temperature, the hotter the sparge the higher the extract. I tend to sparge around 76-77­­­oC, much higher and you can risk extracting unwanted bitter tannins from the grain.

Mash and wort acidification; Increases extract and run off rates, reduces color formation during the boil but does lower hop alpha-acid isomerization meaning you get less bitterness from the hops used (but that’s a different subject). Mash and wort pH can be tinkered with via various water treatments, the use of acid malts (often used in pilsner and pale lager formulations) and decoction mashing.


A final and very valuable factor is volume; Stopping the run off from the mash tun early leaves you with lesser volume of wort at a higher gravity than if the total volume was collected. Some brewers do this on purpose to then liquor back a controlled volume and hit target gravity, a method called high gravity brewing.


However taking these factors into consideration I have no clear explanation for the reading. The only logical one is that the base malt used was from a stray bag of marris otter at work that was delivered by accident and no malt spec was available for it, so I had to guess at the extract alittle.

13 comments:

Ed said...

I've occasionally had a similar problem, though thankfully not recently.

Was this beer stronger than your usual brews? I've found with deeper mash beds I get less extract.

It's also easier to hit target gravity if you aim slightly over and liquor back, diluting your bitter wort until you get what you're after.

Whorst said...

I batch sparge and get 60% efficiency ALL the time. It never fails. At this stage, I'm happy with 60% because I can dial in just about any recipe. The only time I got below 60% was when I used too much lactic acid to lower mash pH. I think I got 58% efficiency on that one. My guess is you probably got a bag of malt that saw better days.

The Urban Brewer said...

I suspect you were right about the malt not being up to scratch. It's bound to happen every now again with the smaller more traditional maltsters (assuming thats who you get your malt from) working flat out these days and therefore occasionally a batch of barley gets rushed through the malting process resulting in some under-modification.

Otherwise, depending on your water supply variability, perhaps your water company has recently changed the source, playing havoc with your pH?

Whorst said...

There is not a great deal of variability with my water supply. As an example, from the water report, it lists Alkalinity at 110 as CaCo3. The range of detections are 100-121. I've got water reports from 5 years back and they're all very consistent. In the case I mentioned, I used an excessive amount of lactic acid. I could tell by viewing the first runnings through the refractometer that something was not right. Now, for a mash with 100% pale malt, I use about .6cc's in the mash. That's using 88% lactic acid. That seems to drop the alkalinity in the 25-30 range. The gypsum and calcium chloride additions I add also drop the alkalinity a tad, but that's another topic all together.e

Rob said...

Well Ed it is marginally stronger but I do vary them allot. I have never had the same problem with brews under 1.050 though. But today I sampled some malt from the source bag but it didnt seem obviously under modified. I will be having words with the water board though, as the water analysis I do have is from alittle while back.

The Urban Brewer said...

Wurst, I wish I had your CaCo3 levels....I have 282 (but fairly tight range 281-284)

Good luck Rob, nobody likes a brew gone wrong but sometimes trying to find the explanation is quite interesting....if not too frustrating!

Anonymous said...

I'm gone to convey my little brother, that he should also visit this blog on regular basis to obtain updated from most recent information.

Also visit my website - www.tedxyse.com

Anonymous said...

Nice post. I was checking constantly this blog and I am impressed!

Extremely helpful info particularly the last part :) I care for such
information a lot. I was seeking this certain information
for a long time. Thank you and best of luck.


Feel free to surf to my homepage: Christian Louboutin Sale

Anonymous said...

Its like you read my mind! You seem to know a lot about this,
like you wrote the book in it or something. I think that you can
do with some pics to drive the message home a bit, but instead of that, this is fantastic blog.
A great read. I will definitely be back.

my blog :: Recommended Reading

Anonymous said...

Hey! Do you know if they make any plugins to safeguard against hackers?
I'm kinda paranoid about losing everything I've worked hard on.
Any recommendations?

Here is my website Sac Louis Vuitton Pas Cher

Anonymous said...

Hey There. I discovered your blog the use of msn. This is an extremely smartly written article.
I will make sure to bookmark it and come back to learn more of your
helpful info. Thank you for the post. I will definitely return.



My web-site - Wholesael NFL Jerseys

Anonymous said...

Today, I went to the beach with my kids. I found a sea shell and gave
it to my 4 year old daughter and said "You can hear the ocean if you put this to your ear." She put the shell to her ear and
screamed. There was a hermit crab inside and it pinched her ear.
She never wants to go back! LoL I know this is entirely off topic but
I had to tell someone!

Also visit my site - Cheap NFL Jerseys

Anonymous said...

Hi there, I enjoy reading through your article post.
I like to write a little comment to support you.


my web blog ... Nike ID